virtualisation:kvm
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | |||
|
virtualisation:kvm [2018/12/04 10:46] Luc Nieland |
virtualisation:kvm [2020/02/13 17:05] (current) Luc Nieland CentOS-8: bond + vlan + bridge |
||
|---|---|---|---|
| Line 347: | Line 347: | ||
| - | =====Distribution: CentOS 6.0 ===== | + | =====Distribution: CentOS ===== |
| ===preparation=== | ===preparation=== | ||
| - | Install a minimal CentOS 6.0 system with a static IP-number. | + | Install a minimal CentOS system with a static IP-number. |
| + | |||
| + | |||
| + | |||
| + | ===network config CentOS-8=== | ||
| + | |||
| + | With nmcli | ||
| + | |||
| + | Add to /etc/sysconfig/ | ||
| + | |||
| + | Bonding: | ||
| + | <code> | ||
| + | nmcli con add type bond con-name bond0 ifname bond0 autoconnect yes \ | ||
| + | ipv4.method disabled \ | ||
| + | ipv6.method ignore | ||
| + | nmcli con add type ethernet ifname eno1 con-name bond0-sl1 master bond0 | ||
| + | nmcli con add type ethernet ifname eno2 con-name bond0-sl2 master bond0 | ||
| + | <code> | ||
| + | |||
| + | |||
| + | Split the trunc-datastream to VLAN's: | ||
| + | <code> | ||
| + | nmcli con add type vlan ifname vlan20 con-name vlan20 vlan.id 20 \ | ||
| + | vlan.parent bond0 \ | ||
| + | ipv4.method disabled \ | ||
| + | ipv6.method ignore | ||
| + | # repeat per VLAN | ||
| + | <code> | ||
| + | |||
| + | |||
| + | Create a bridge per VLAN: | ||
| + | <code> | ||
| + | BR_NAME="br20" | ||
| + | BR_INT="vlan20" | ||
| + | SUBNET_IP="192.168.103.32/24" | ||
| + | GW="192.168.103.1" | ||
| + | DNS1="192.168.102.144" | ||
| + | DNS2="192.168.102.146" | ||
| + | nmcli connection add type bridge con-name ${BR_NAME} ifname ${BR_NAME} autoconnect yes | ||
| + | nmcli connection modify ${BR_NAME} ipv4.method manual ipv4.addresses ${SUBNET_IP} | ||
| + | nmcli connection modify ${BR_NAME} ipv4.gateway ${GW} | ||
| + | nmcli connection modify ${BR_NAME} ipv4.dns ${DNS1} +ipv4.dns ${DNS2} | ||
| + | nmcli connection up ${BR_NAME} | ||
| + | nmcli connection add type bridge-slave con-name ${BR_INT} ifname ${BR_INT} master ${BR_NAME} autoconnect yes | ||
| + | nmcli connection up ifname ${BR_INT} | ||
| + | # | ||
| + | ip r add default via 192.168.103.1 | ||
| + | # | ||
| + | <code> | ||
| + | |||
| + | ===hypervisor kvm=== | ||
| Install the software: | Install the software: | ||
| yum install kvm virt-manager libvirt | yum install kvm virt-manager libvirt | ||
| + | |||
| + | |||
virtualisation/kvm.1543916804.txt.gz · Last modified: 2018/12/04 10:46 by Luc Nieland
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
